Software Name: Hinson Configuration Software

Software Version: V1.5.8

Release date: 2025.10.27

Applicable systems: Windows 7 and later

Language: Chinese/EN

Applicable products:

FE Series, LE Series, HE Series, SE Series, DE Series, ME Series, CNS-MGS-08/N, CNS-MGS-16/N, CNS-MGS-080N/D, CNS-MGS160S, CNS-MGS160N/D, CNS-MRS-L2, CNS-MRS-xxxN, CNS-RFID-01/N, CNS-RFID-1S/N, CNS-WRFID-01, CNS-BLD-1S, CNS-STDR-2L/N, CNS-STDR-2M/N, CNS-BL30HB, CNS-BL30HB/N, CNS-BLD-02, CNS-BLD-2S/N, CNS-BLD-2L/N, CNS-BLDC-2S-NC, CNS-BLDC-2L-NC, CNS-BL30HDN, CNS-MI50HDN, CNS-STDR-2L-NC, CNS-STDR-2M-NC, CNS-BL30HSN, CNS-MI50HSN, CNS-RELAY-01, CNS-MFIO-01, CNS-MFIO-02/N, CNS-MFIO-2M, CNS-EMAG-ABS, CNS-GYRO-Z1.

Hinson 1.5.8 Updated on 2025-10-27

CNS-HE-3051
Version Information: 1.6.0
Update date: 20251027
Update content:
1) Dedicated version for subnet mask and default gateway parameters

Hinson 1.5.8 Updated on 2025-9-29

CNS-LE-XXXX
Version Information: 1.3.15
Update date: 20250929
Update content:
1) Added new parameters: high-reflectivity plate recognition, high-reflectivity plate threshold, and NTP time synchronization. This feature is supported by sensor firmware versions V1.3 and later.
2) Added a point cloud mode selection feature. This feature is supported by sensor firmware versions V1.3 and later.
3) When opening the configuration file, parameters from the previous version of the file can be recognized.

Hinson 1.5.6 Updated on 2025-9-1

CNS-LS05
Version Information: 1.3.9.4
Updated date: 20250619
Update content:
1) Parameter settings disable wheel adjustment;

CNS-RFID-1S-01 Configuration Software
Software version: 1.1.0: Compatible with firmware version V3.0.0
1.0.0 CNS-RFID-1S Configuration Software.
1.1.0 Added an RSSI signal filtering configuration feature.
1.1.1 Added the CANOpen protocol; the number of bytes for read and write operations has been changed to 16 bytes.

CNS-RFID-1SN-01N Configuration Software
Software version: 1.1.0: Compatible with firmware version V3.0.0
1.0.0 CNS-RFID-1S Configuration Software.
1.1.0 Added an RSSI signal filtering configuration feature.
1.1.1 Added the CANOpen protocol; the number of bytes for read and write operations has been changed to 16 bytes.

CNS-HE-xxxx configuration software
Version Information: 1.5.4
Update date: 20250829
Update content:
Compatible with sensor firmware version V2.3.0
1) Added NTP time synchronization and reflector detection configuration.
2) Added NTP protocol

Hinson 1.5.6 Updated on 2025-02-15

CNS-FE-XXX
Version Information: 1.2.3
Updated date: 20250221
Update content:
1) When the mouse position is changed on the page field, the corresponding angle detected by the sensor is displayed.
2) Added a feature to display the sensor detection distance and reflectance intensity corresponding to the mouse cursor’s position on the page fields.
3) Added a new gradient mode for reflecting intensity in drawing mode.
4) IP address range modification

CNS-PHR-XXX
Version Information: 1.1.0
Updated date: 20250303
Update content:
1) English and Chinese translations cover all fields.
2) Optimize the save settings parameter and read settings parameter functions.

CNS-OPCA-ETxx
Version Information: 1.0.2
Updated on: 20240806
Update content:
1) The IP address can be set manually.
2) Optimize the sensor IP address search method

Hinson 1.5.6 Updated on 2025-02-10

CNS-FE-XXX
Version Information: 1.2.2
Update date: 20250214
Update content:
1) Product type field information changed
2) Enable status change of sensor control mode

Hinson 1.5.6 Updated on 2025-01-17

CNS-FE-XXX
Version Information: 1.2.1
Updated date: 20241219
Update content:
Update content:
1) Optimized the pop-up interface for connection failure.
2) Add a prompt box asking whether to restart after the download takes effect.
3) Optimize the method for searching sensor IP addresses
4) Add sensor status feedback display

CNS-LS05
Version Information: 1.3.9
Update date: 20250117
Update content:
1) Menu Function – Open File: Optimize the way text data is recognized.

Hinson 1.5.6 Updated on 2024-12-10

Version Information: 1.3.8
Updated date: 20241210
Update content:
1) Configurable parameters: multiple echo selection, dirt filtering distance, dirt filtering intensity, and trailing-edge filtering level.
2) Optimized the pop-up interface for connection failure.

Hinson 1.5.6 Updated on 2024-10-08

CNS-PHR-xxx

Version Information: 1.0.2
Updated on: 20240910
Update content:
1) Optimize the Chinese-English switching function on the host computer;

CNS-FE-xxx

Version Information: 1.1.0
Updated on: 20240630
Update content:
1) Add multi-echo setting and mirror contamination filtering setting;

Hinson 1.5.5 Updated on 2024-08-21

CNS-TDCS-xxx
Version Information: 1.4.0
Updated date: 20240821

CNS-HE-XXX
Version Information: 1.5.2
Updated date: 20240821
Update content:
1) Chinese-English translation optimization
2) Optimize UDP connections

CNS-LE-XXX
Version Information: 1.3.10
Updated date: 20240821
Update content:
1) Chinese-English translation optimization
2) Optimize UDP connections

CNS-LS05 V1.3.7

Version Information: 1.3.7
Updated date: 20240821
Update content:
1) Chinese-English translation optimization
2) Optimize UDP connections

Hinson 1.5.5 Updated on 2024-08-16
CNS-HE-XXX
Version Information: 1.5.2
Updated on: 20240815
Update content:
1) Interface optimization
2) Add a prompt box asking whether to restart after the download takes effect.
3) Add sensor mounting in both upright and inverted orientations, along with configuration and display settings.
4) Add sensor status feedback display
5) Add profile information, including the software version and save date.
6) Optimize the method for searching sensor IP addresses
7) Fixed the TCP connection interruption and reconnection issue.
8) IP address range
9) Optimization of the pop-up interface for connection failure notifications

CNS-LE-XXX V1.5.1
Version Information: 1.3.9
Updated on: 20240815
Update content:
1) Interface optimization
2) Add a prompt box asking whether to restart after the download takes effect.
3) Add sensor status feedback display
4) Add configuration file information, including the software version and save date.
5) Optimize the method for searching sensor IP addresses
6) Fixed the TCP disconnection and reconnection issue.
7) IP address range
8) Optimized the pop-up interface for connection failure.

CNS-LS05 V1.3.6

Version Information: 1.3.6
Updated on: 20240815
Update content:
1) Interface optimization;
2) Logical restrictions on IP addresses;
3) Software version compatibility issues;
4) Point cloud interface displays offset;
5) Add a prompt box asking whether to restart after the download takes effect;
6) Add forward and reverse installation and display settings for sensors;
7) Add sensor status display;
8) Add configuration file information, including the software version and save date;
9) Improve point cloud display and fix the issue where the interface displayed an incorrect angle deviation of 0.5° from the actual value.
10) The distance data and reflectance intensity data in the data list correspond to the installation orientation.
11) Fix the host computer logic for both correct and reversed sensor installation;
12) Optimize the IP address search method
13) After fixing the TCP disconnection, internally reset the TCP;
14) Added support for baud rate 460800 in version 2.5.1 of models SE-0533 and SE-1033;

CNS-OPCA-ETH

Version Information: 1.0.3
Updated on: 20240620
Update content:
1) The host computer is compatible with both new and old sensor parameters.

USB driver

Version Information
Updated to version 20240630;

Debugging tool:
Network debugging update: netassist 5.0.13
Added serial port debugging assistant: urtassist5.0.13

Hinson 1.5.5 Updated on 2024-07-22
CNS-LS05 updated to V1.3.6
1) Optimized the display issue of channel numbers at high zoom levels;

Hinson 1.5.5 Updated on 2024-4-07
1) Configuration software update: CNS-LE-xxx V1.3.6, 20240407
a) Optimize point cloud display by changing invalid points to gray;
b) Supports firmware version V1.9.0 and adds a trailing filter level;
2) Configuration software update: CNS-HE-xxx V1.3.2, 20240103
a) Supports firmware version V1.9.0 and adds trailing filter levels;
3) Update configuration software: CNS-DE-xxx V1.1.1 2024060101
a) Added the function to bind the local IP address;
b) IP address range modification;
4) Newly added configuration software
a) CNS-SF30HB,
        
b) CNS-SF30HDN

c) CNS-SF30HSN

d) CNS-TDCS-xxx;

e) CNS-PHR-xxx;

f) CNS-OPS-xxx;

g) CNS-FE-xxx;

g) CNS-ET-xxx;

g) CNS-FE-xxx;

Updated on 2024-2-22
1) Update configuration software: CNS-LS05 V1.3.4
a) Optimize the interface to resolve the issue where channel numbers become invisible due to scaling problems.
b) Software version compatibility issues—use a unified version to compile the software.
c) Fix the issue where the point cloud display interface deviated from the actual orientation by 0.1°;

Updated on 2024-1-27
1) Update configuration software: CNS-WRFID-01-V2_20240126
Added English support;
2) Newly added configuration software: SE-05-10XXF series, 20240223
Supports multi-echo version
3) New configuration software: HE-3091F 20231122
Supports multi-echo version
4) New configuration software: HE-3081 20231228
          
5) Newly added configuration software: OPCA-ET 20231019
Supports OPCA-ET subnet mask configuration and gateway configuration;
6) Newly added configuration software SE-1022F16 020240104
Supports drawing shielding areas.

2023-12-20

1) USB driver version update;
2) Add two Ethernet debugging tools;
3) Add configuration software for HE-3091F.

Configuration Software V1.5.4 2023-07-20

CNS-LS05 V1.3.2 230720
1) Start configuring IP addresses from the 10.x network segment;

Configuration Software V1.5.4 2023-03-02

CNS-HE-XXXX software

Update to V1.1.1
1) Start configuring IP addresses from the 10.x network segment;

Configuration Software V1.5.4 2022-08-07

Add CP210X port driver
Add a serial port debugging assistant.
Add a Modbus debugging assistant.

CNS-HE-XXXX software

Update to V1.2.0
1) Added a configuration option for crosstalk filtering. Optimized point cloud display; this feature is supported by HE-series sensors version V1.3 and later.

CNS-LE-XXXX software

Update to V1.3.3
1) Added a configuration option for crosstalk filtering. Optimized point cloud display; this feature is supported by LE-series sensors version 1.7 and later.

V1.5.3 Configuration Software

CNS-30HDN software
Functional testing: In navigation mode, fixed the bug where the STOP button failed to stop effectively.
Add
1) Supports DE series configuration software;
2) Supports HE series configuration software;

CNS-HE-XXXX software

Update to V1.1.0
1) Resolve the issue of needing to disconnect other network connections when establishing a connection;

CNS-LE-XXXX software

Update to V1.3.2
1) Resolve the issue of needing to disconnect other network connections when establishing a connection;

CNS-SE-XXXX software

Update to V1.3.2
1) Resolve the issue of needing to disconnect other network connections when establishing a connection;

CNS-ME-XXXX software

Update to V1.1.0
1) Resolve the issue of needing to disconnect other network connections when establishing a connection;

CNS-DE-XXXX software

Update to V1.1.0
1) Resolve the issue of needing to disconnect other network connections when establishing a connection;

V1.5.2 Configuration Software

CNS-LE-xxx software
V1.3.0: Supports firmware version 1.2 and adds configuration parameters for the crosstalk function;

CNS-GYRO-Z1
V1.0 Fixed configuration errors in the CAN-HS and Modbus protocols.
 

V1.5.1 Configuration Software

CNS-LS05 Software
V1.3.0 1) Added support for SE-0535/SE-1035 programs in version V1.9;
2) Supports multi-segment IP address configuration;
3) Resolve the pop-up window caused by runtime library version incompatibility;

CNS-ME-xxx-Software
V1.1 Added support for the V1.9 version of the program;
Supports multi-segment IP address configuration;

CNS-LE-xxx software
V1.2.1 Fixed the pop-up window bug;
Add restrictions on IP address settings.